| Standard cable FR |
200063 |
This 5 pin cable is supplied standard with any /FR screwdriver. Length: 98.4 in. |
| Standard cable TA |
250063/N |
This 8 pin cable is supplied standard with any /TA torque & angle screwdriver. Length: 98.4 in. |
| Tool balancers TECBA1 |
010300 |
New tool balancers TECBA1, code no. 010300, allow screwdrivers to be positioned over the work station for comfortable operation. Models with higher capacity available on request. |
| ARMPV1 support arms |
010500 |
ARMPV1 support arms, code 010500, consist of a vertical support on which a 180° pivoting arm is attached. |
| Double output connector DOCK01 |
020020 |
A double output connector is available for operators using two FAB or RAF screwdrivers in the same working area. One end is to be connected to the controller (cable included), the other end to the drivers. Screwdrivers not to be used at the same time |
| Double output connector DOCK04 |
020045 |
A double output connector is available for operators using two PLUTO screwdrivers with EDU2AE/TOP in the same working area. The screwdrivers cannot be used at the same time. |
| Double output connector DOCK04/TA |
020045/TA |
A double output connector is available for operators using two PLUTO screwdrivers with EDU2AE/TOP/TA in the same working area. The screwdrivers cannot be used at the same time. |
| Extension ring KP05 |
234511/K |
KP05, code 234511/K, is an extension ring to be used with Pluto inline drivers for easier clamping on reaction arms. |
| Angle Head FAB – ANG HD1 |
010100 |
When space is limited a right angle head can be easily attached to lever start FAB screwdrivers. ANG HD1 is the cost effective alternative to ANG HD8. 1/4” hex – max torque 53 in/lbs. |
| Angle Head RAF – ANG HD2 |
010120 |
When space is limited a right angle head can be easily attached to lever start RAF screwdrivers. ANG HD2 is the cost effective alternative to ANG HD9. 1/4” hex – max torque 53 in/lbs. |
| Angle Head FAB – ANG HD8 |
010143 |
When space is limited a right angle head can be easily attached to lever start FAB screwdrivers. Model ANGHD8, code 010143, is suitable to FAB series. 1/4” hex – max torque 53 in/lbs. |
| Angle head RAF – ANG HD9 |
010144 |
When space is limited a right angle head can be easily attached to lever start RAF screwdrivers. Model ANGHD9, code 010144, is suitable to RAF series. 1/4” hex, max torque 53 in/lbs. |
| Angle head – ANG HD10 – 133 in/lbs |
010145 |
ANG HD10 Angle Head may be used with all Pluto Inline Drivers for applications with limited access with torque up to 133 in/lbs. 3/8” square |
| Angle Head PLUTO – ANG HD11 – 70 in/lbs |
010146 |
ANGHD11 may be used with all Pluto Inline Drivers for applications with limited access. This heavy duty angle attachment also includes an adaptor that connects Pluto Driver. 1/4” hex, max torque 70 in/lbs. |
| Angle Head PLUTO – ANG HD12 – 177 in/lbs |
010147 |
ANG HD12 Angle Head may be used with all Pluto Inline Drivers for applications with limited access with torque up to 177 in/lbs. 3/8” square |
| Angle Head KBL – ANG HD15 – 13 in/lbs |
010152 |
ANGHD15 can be used with KBL04FR, KBL15FR, KBL04FR/S and KBL15FR/S inline Driver for applications with limited access. 1/4” hex, max torque 13 in/lbs. |
| Angle Head KBL – ANG HD16 – 26 in/lbs |
010153 |
ANGHD16 can be used with KBL30FR and KBL30FR/S inline Driver for applications with limited access. 1/4” hex, max torque 26 in/lbs. |
| Socket tray for TOP unit |
020042 |
When using a multiple torque system a socket tray can be a useful accessory for program selection. It’s very easy to use: the control unit automatically selects the correct preset program when a bit or socket is removed. |
| Switchbox for TOP unit |
020033 |
A switch box can be a useful accessory for multiprogram selection. It’s very easy to use: each time a button is pushed, the control unit automatically selects the preset program. |
| KBL clutch cover |
02002- 02002-/CA |
Clutch cover for KBL. Code 020028 for KBL04-15FR; Code 020028/CA for KBL04-15FR/CA; Cod. 020029 for KBL30FR; Code 020029/CA for KBL30FR/CA. |
| Autocatcher |
01011- |
An Autocatcher allows the operator to to pick up and fasten stainless steel, brass, copper and plastic screws by using one hand! Sizes available: AC2.3 for M2 to M3, code 010113, AC3.5 for M3 to M5, code 010114. |
| ACE Screw Counter |
02002- |
The ACE screw counter is a process control system that monitors the fastening assembly process. It tracks, in real time, the fastening of each screw in an assembly, then notifies the result. |
| Telescopic Spindle |
8003– |
The Telescopic Spindle (axial compensator) is used in multi spindle applications to balance the screw tightening process and compensate depth difference across multiple fasteners. |
| Coloured Rings |
2000– |
Coloured rings are useful to distinguish and identify different screwdrivers at a glance. Available in different colours: Code 200085 – Blue Code 200086 – Red Code 200087 – Yellow Code 200088 – Green Code 200089 – Black |
| Barcode reader BRCR90 |
020050 |
The BRCR90 barcode reader allows the operator to instantly select the program previously set on the control unit. To be used with EDU2AE/TOP or EDU2AE/TOP/TA. |
| Serial Printer PRNTR1 |
020026 |
The PRINTR1 serial printer gives the possibility to instantly print the results of each tightened screw. It works with EDU2AE/TOP, EDU2AE/TOP/TA, EDU2AE/HPRO control units and K and Mini K../S torque testers. |
| Ethernet Device |
020075 |
Kolver Ethernet Device (code 020075) makes it possible to connect a PC to any EDU 2AE/TOP – TOP/E – TOP/TA via remote LAN connection. |
| Cable with strain relief |
250063/H |
The cable with spring is more resistant thanks to a longer connector and spring, which makes the cable up to 4 times more endurable. Perfectly compatible with any 5 pin (code 200063/H) or 8 pin (code 250063/H) screwdriver/control unit. |
| Light stack |
020080 |
The light stack allows better visibility of output signals. Made for any control unit with signals. Supplied standard with 2,5m cable and 10pin connector for CN1 (EDU2AE – EDU2AE/TOP). Wiring for other Kolver control units available on request. |
| Start / Reverse Pedals |
020070 |
Start and reverse signals can now be activated using our new foot pedal. Supplied standard with 3,5 m cable and connector for any EDU2AE and EDU2AE/TOP unit. |
| A2 and A3 Suction Heads |
010111/- |
A suction head is the best way to handle non-magnetic screws (stainless steel, brass, plastic etc.). Available in two models: A2 for M2-M2,6 screws (code 010111/1) and A3 for M3-M4 screws (code 010111/2). A2 and A3 can be installed on any screwdriver |
| ASP HD Suction Heads |
0101– |
A Suction Head is the best way to handle non-magnetic screws (stainless steel, brass, plastic etc). Available for NATO 15 (ASP HD6, code 010117), NATO50 (ASP HD7, code 010118), MITO15 (ASP HD8, code 010119) and PLUTO3-15 (ASP HD9, code 010121). |
| RIV HD Bit Guides |
01018x |
Bit Guides are the best accessory to help long bits, wire thread insert and riveters keep the correct perpendicular position. For PLUTO and KBL screwdrivers. |
| Reduced Front Ring for PLUTO |
234515 |
Inline PLUTO screwdrivers can be supplied with reduced front ring (code 234515). The new reduced front ring, code 234515, is also available as accessory/spare part and supplied with four M3x6 screws. |
